lps360-m series 360 watt ac-dc power supply total power: 200 - 360 w input voltage: 90 - 264 vac 120 - 300 vdc outputs: single special features ? medical and ite safeties ? active power factor correction ? 3 x 5 footprint ? less than 1u high ? en61000-3-2 compliant ? remote sense ? power fail ? adjustable main output ? level b conducted emi - class i or class ii inputs ? overvoltage protection ? overload protection ? thermal overload protection ? 12 v fan output ? lpx200 enclosure kit available ? 5 v standby output ? remote inhibit ? pmbus commands ? rohs compliant ? digital i 2 c interface ? designed to meet class i and class ii ? dual ac fuses ? suitable for bf type applications safety ? tuv 60950, 60601-1 ? ul 60950, 60601-1 ? culus 60950, 60601-1 ? cb certifcate & report ? ce mark (lvd & emc) ? ccc approval electrical specifcations input input ra nge 90 - 264 vac; 120 - 300 vdc frequency 47 - 63 hz inrush current 50 a max., cold start @ 25 c effciency up to 93% at full load emi/rfi fcc class b conducted; cispr22 class b conducted; en55022 class b conducted; vde0878pt3 class b conducted power factor 0.99 typical safety ground leakage current 150 a @ 132 vac, 60 hz for class i, 300 a @ 264 vac, 60 hz for class ii output maximum power 200 - 240 w (see de-rating) for convection, 360 w with 400 lfm of forced air adjustment range 12 v and 24 v models, -0%, +15%; 15 v and 48 v models, -5%, +10%; 36 v model, -15%, +0% standby output 5 v @ 1a convection, 2 a with forced air fan output 12 v @ 0.5 a convection, 1 a forced air hold-up time 20 ms @240 w, 220 vac input; 12 ms @ 360 w overload protection short circuit protection on all outputs. case overload protected @ 110 - 160% above rating overvoltage protection 15 - 50% above nominal output logical control power failure open collector logic signal goes high 100 - 500 msec after main output; it goes low at least 6 msec before loss of regulation remote sense compensates for 0.5 v lead drop min. will operate without remote sense connected. reverse connection protected. low power data sheet power
environmental specifcations operating temperature -20 c to 50 c ambient, derate each output as 2.5% per degree from 50 c to 70 c; -40 c startup if standby output 1a (any valid load on main output); -30 c startup if standby output > 1a (any valid load on main output) storage temperature -40 c to +85 c electromagnetic susceptibility designed to meet en61000-4; -2, -3, -4, -5, -6, -8, -11 level 3 humidity operating; non-condensing 10% to 95% rh vibration iec68-2-6 to the levels of iec721-3-2 mtbf calculated >2 million hours at full load and 25 c ambient conditions. 230 vac input, bellcore ordering information model number output voltage minimum load maximum load with convection cooling maximum load with forced air peak load regulation 2 ripple p/p (pard) 3 lps363-m 12 v 0 a 20 a 30 a 39 a 2% 120 mv lps364-m 15 v 0 a 16 a 24 a 31 a 2% 150 mv lps365-m 24 v 0 a 10 a 15 a 19.5 a 2% 240 mv LPS366-M 36 v 0 a 6.25 a 4 11.25 a 4 14.62 a 2% 360 mv lps368-m 48 v 0 a 5 a 7.5 a 9.75 a 2% 480 mv 1. peak current lasting <3 seconds. 2 . at 25 c including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3 . peak-to-peak with 20 mhz bandwidth and 10 f (tantalum capacitor) in parallel with a 0.1 f capacitor at rated line voltage and load ranges. 4. LPS366-M is limited to the lower of the applicable power rating or current rating, whichever results in lowest power. 5. this product is a component power supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. emc compliance to appropriate standards must be verifed at the system level. this product is for sale to oems and system integrators, including through distribution channels. it is not intended for sale to end users. pin assignments connector lps360-m j4 pin 1 line pin 3 neutral barr barr-1 main output + barr-2 main output common j5 pin 1 +v1 remote sense pin 2 -v1 remote sense pin 3 +5 v standby pin 4 5 v standby return pin 5 +power fail pin 6 ** forced air operation pin 7 inhibit pin 8 gnd pin 9 sda pin 10 scl j3 pin 1 +12 v fan pin 2 12 v fan return (isolated) ** for forced air operation, connect pin 6 to pin 8 of j5. mating connectors j4 ac input molex 09-50-3031 (connector) pins: 08-52-0072 j6 ac ground molex 01-90020001 dc output (barr) molex 19141-0058/0063 or 19099/0048 spade lug based on cable ampacity/awg j5 control signals molex 90142-0010 (usa) pins: 90119-2110 j3 fan output molex 51065-0200 pins: 50212-8100 the artesyn connector kit #70-841-029, includes all of the above. 1. specifcations subject to change without notice. 2. all dimensions in inches (mm), tolerance is 0.02(0.5 mm) 3. mounting holes mh1 and mh2 should be grounded for emi purposes. 4. mounting hole mh1 is safety ground connection. 5. specifcations are for convection rating at factory settings at 115 vac input, 25 c unless otherwise stated. 6. this power supply requires mounting on metal standoffs 0.20 (5m) in height. 7. warranty: 3 years 8. weight: 0.4kg / 0.88 lb (lps363-m) lps360-m series data sheet digital i 2 c interface accessories 73-769-001 usb to i 2 c adapter with usb cable 73-841-030 lps360-m i 2 c mating connector artesyn connector kit #73-769-005 includes both of the above
worldwide offices americas 2900 s.diablo way tempe, az 85282 usa +1 888 412 7832 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom +44 (0) 1384 842 211 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong +852 2176 3333 for more information: www.artesyn.com/power for support: productsupport.ep@artesyn.com www.artesyn.com artesyn embedded technologies, artesyn and the artesyn embedded technologies logo are trademarks and service marks of artesyn embedded technologies, inc. all other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. ? 2016 artesyn embedded technologies, inc. all rights reserved. for full legal terms and conditions, please visit www.artesyn.com/legal. lps360-m series data sheet lps360-m ds 18mar2016 mechanical drawings performance data 3 [ 7 6 , 2 ] 5 [ 1 2 7 ] 4 , 5 5 [ 1 1 5 , 6 ] 2 , 5 5 [ 6 4 , 8 ] 4 x 0 , 1 6 [ 4 ] j 5 p i n n u m b e r i n g 1 5 6 1 0 b a r r 1 ( + ) b a r r 2 ( - ) m 4 x 0 . 7 p j 5 j 3 j 4 g r o u n d t a b ( j 6 ) p i n 1 p i n 3 v r 1 o u t p u t v o l t a g e a d j u s t m e n t p o s t pin 1(+v1 remote sense) 1.36 [34.60] 0.197 minimum standoff height [5.00]
|
